CruzPro

Spare gas sensor assembled with 16-ft cable (5 meters) for use with GD-20B and GD-25 gas detector meters.Model#  GD-27 CruzPro GD-20B Information: CruzPro GD-20B Manual ...

CruzPro T60 Digital Water Temperature Gauge displays engine oil or water temperature in degrees F or C. The T-60 has built-in calibration curves for most popular temperature senders manufactured by VDO, Teleflex, Faria, Stewart-Warner and others (sender not provided). When activated, the built-in 85 dB alarm will sound and the display will flash. The T60 alarms can be enabled or disabled with a single key press. Also, the CruzPro T60Digital Water Temperature Gauge draws only 0.017...

CruzPro OP60 Oil Pressure Gauge unique, low and high pressure alarms. NMEA 0183 Data Output.Preprogrammed for popular senders from VDO, Teleflex, Faria, etc. The OP-60 Oil Pressure Gauge displays engine oil pressure in Psi or Bars. Model#: OP-60R Round OP-60S Square OP60 Digital Oil Pressure Gauge Specifications: Supply Voltage:  9.5 - 33.0 VDC  Current Drain:  0.018 amps nominal Display:  4 digit LCD, 5 levels of backlighting Data:  Oil Pressure, 0 to 75, 0 to...

CruzPro RH60 RPM Engine Hours & Elapsed Time Gauge accurate engine RPM monitor with built in setable Alarms, max RPM memory, engine hours, elapsed trip time. NMEA 0183 data output and works with any engine and can be driven from a wide range of signal frequencies and amplitudes. The RH-60 is a four digit digital display of engine RPM, total engine hours, elapsed trip time and maximum r.p.m. seen. Model#: RH-60R Round RH-60S Square RH60 Digital RPM Engine Hours & Elapsed Time Gauge...

CruzPro PY60 Digital Pyrometer Gauge is a low Cost Pyrometer -20 deg C to 1100 deg C. It comes complete with K-type thermocouple. NMEA 0183 data output. The PY-60 displays engine exhaust gas temperature in degrees F or C. Model#: PY-60R Round PY-60S Square CruzPro PY60 Digital Pyrometer Gauge Specifications: Supply Voltage:  9.5 - 33.0 VDC  Current Drain:  0.018 amps nominal Display:  4 digit LCD, 5 levels of backlighting13 levels of display damping...

CruzPro SB2 Dual Sender Buffer allows a CruzPro gauge (FU30/FU60, TL25/TL55, OP30/OP60, etc.) and one existing analog gauge to share a single station 10-180 ohm or 240 -33 ohm sender.  The SB2 Dual Sender Buffer Makes adding a digital gauge to an existing analog set-up very easy. One SB-2 will buffer two separate senders (e.g. an oil pressure and water temperature sender, etc.). Model# SB-2 SB2 Dual Sender Buffer Specifications: Supply Voltage:  10.5 to 33.0...

CruzPro RH110 Digital RPM Engine Hours Elapsed Time Gauge is an accurate Engine RPM Monitor with built in setable Alarms, max RPM memory, engine hours, elapsed trip time with NMEA 0183 data output.The RH-110 works with any engine and can be driven from a wide range of signal frequencies and amplitudes.Model# RH-110CruzPro RH110 Specifications:Operating Voltage: 9.50 - 33.00 VDC Current Drain: 0.035 amps nominal Display: Large 4 digit LCD, 5 levels of backlighting with external backlight on/off...

CruzPro CH60 Intelligent Chain Counter Windlass Controller advises how much chain is out, displays windlass battery voltage, slows windlass, NMEA 0183 data output, etc. The CH-60 chain counter can be programmed to back-jog the chain a few links when you remove your finger from the UP button, removing tension off the chain, capstan and windlass gears increasing windlass life and automatically "parks" the chain into a chain stopper. Model# CH-60R Round CH-60S Square CruzPro CH60...

CruzPro WTP110 Precision Sea Water Temperature Gauge provides accurate sea water temperature to 0.01deg F/C. NMEA 0183 data output and Hi/Lo temperature alarms, trend indicator and Min/Max temp. memory. The WTP-110 Works with standard 10Kohm thermistor transducers (CruzPro THT-1 thru-hull or TMT-1 transom mount transducers below) or popular 30Kohm Dytek temperature senders. Model# WTP-110 WTP110 Sea Temp Gauge Specifications: Operating Voltage:  9.5 - 33.0 VDC ...

CruzPro WTP65 Precision Sea Water Temperature Gauge provides Accurate sea water temperature to 0.1deg F/C. NMEA 0183 data output. The WTP-65 Temperature Gauge works with any standard 10Kohm thermistor temperature transducer or select an optional CruzPro THT-1 thru-hull or TMT-1 transom mount transducers.  Model# WTP-65R Round WTP-65S Square WTP65 Sea Temperature Gauge Specifications: Operating Voltage:  9.5 - 33.0 VDC  Current Drain:  0.018 amps nominal Display: 4...

V55 Digital Volts Gauge provides accurate low cost digital instrumentation for batteries between 9.5 and 33 Volts. You can set independent Low and High voltage alarms. When activated, the V55 built-in 85 dB alarm will sound and the display will flash. Five levels of backlighting can be selected and all set-up, calibration constants and alarm values are saved to non-volatile memory. All constants and calibrations are pre-set during manufacture but you may alter these settings to suit your...

The V60 Digital Volts Gauge provides accurate low cost digital instrumentation for three banks of batteries between 9.5 and 33 Volts. Independent Low and High voltage alarms can be set for each bank. When activated, the V60 built-in 85 dB alarm will sound and the display will flash. Five levels of backlighting can be selected and all set-up, calibration constants and alarm values are saved to non-volatile memory. All constants and calibrations are pre-set during manufacture but you may alter...

CruzPro VAH65 Digital Volts Amp Three Battery Banks provides accurate low cost digital instrumentation for three banks of batteries between 9.5 and 33 Volts. The VAH-65 displays battery voltage for three banks and charging or discharge current and tells you how much battery capacity has been consumed and how much is remaining in your main house bank. It keeps track of all current entering and leaving the battery and applies the appropriate Peukert's and efficiency factors. You can set Low and...

CruzPro FU60 Fuel Consumption Computer Fuel Gauge displays fuel remaining in gallons, liters or percent (0-100%) in tenths, fuel used (gallons or liters), and fuel consumption rate (gallons/hour or liters/hour). The CruzPro FU-60 digital fuel gauge is a plug-in replacement for your regular analog fuel gauge. No need for special flow sensors. The FU60 works with your standard fuel sender manufactured by Centroid, Aerotech, VDO, Teleflex, Faria, GM, Stewart-Warner and others to compute...

VAH110 Digital Volts Amp hours three banks monitor provides accurate low cost digital instrumentation for three banks of batteries between 9.5 and 33 Volts.  The VAH-110 displays battery voltage for three banks and charging or discharge current and tells you how much battery capacity has been consumed and how much is remaining in your main house bank. It keeps track of all current entering and leaving the battery and applies the appropriate Peukert's and efficiency factors. You can...

CruzPro TL55 Digital Tank Level Gauge and Alarm/w Transfer Pump control provides a digital display for tank level. Level can be displayed in liters/gallons or percent (0-100%) up to 999 and as a percentage (0-100%) up to 6500 liters/gallons. The TL55 Digital Tank Level Gauge has been pre-programmed to work with all known resistive type level senders with 0-30, 0-70, 0-90, 10-73, 10-180, 33-240, 40-250 ohm (and their revere) outputs made by VDO, Teleflex, Mercury, GM, Stewart-Warner,...

ETM20 Engine Exhaust Temperature Monitor and Alarm uses modern electronics and a reliable solid state temperature sensor to accurately monitor the temperature at any point it is attached. The alarm is factory pre-set at 90 degrees C (194 deg F) but can be easily adjusted with a small screwdriver over a range of 50 deg C to 125 deg C (122 to 257 deg F). When the ETM-20 detects an over-temperature condition it sounds a built-in 85 dB audible alarm. The alarm will continue to sound for the...

CruzPro Transom Mount Speed Temperature Transducer TMST 1

CruzPro TL60 Digital Tank Level Gauge clever very accurate, provides an accurate digital display for three tanks. Model#  TL-60R Round TL-60S Square TL60 Digital Tank Level Gauge Specifications: Operating Voltage:  9.5 - 33.0 VDC  Current Drain:  0.018 amps nominal Data:  Tank Level Display for Three Tanks External Outputs/Alarms:  The NMEA 0183 data output terminal may be programmed as an external alarm output Inputs: Tank Level Senders: All...