Display and Remotes

CruzPro T65 Digital Temperature Display continuously monitors three separate sensors and displays temperature from -20 deg F (-29 deg C) to +140 deg F. (+60 deg C). The T-65 comes factory calibrated but can be user calibrated in the field for each individual sensor for spot-on accuracy. All set-up and calibration constants are saved to non-volatile memory. The T65 uses standard 10K NTC thermister temperature sensors (the type most often used in speed/temperature and depth/temperature...

Go Power Pure Sine Wave Inverter Remote GP-SWR-A features an LED indicator showing inverter status, ON/OFF switch and 25' of cable. The Remote GP-SWR-A can be used with all GP-ISW inverters, the GP-HS1500, GP-SW1000, GP-SW-2000, and GP-SW3000 inverters. GP-SWR-A is compatible with both 12V & 24V inverters. Remote GP-SWR-A Specifications: Dimension (LxWxH) mm (Inches): 55 x 28 x 73 (2.2 x 1.1 x 2.9) Weight (kg/lbs): 0.1 / 0.05 Warranty: 2 years Go Power GP-SWR-A Documents: GP-SWR-A Specsheet...

The LinkLITE / LinkPRO battery monitors selectively displays voltage, charge and discharge current, consumed amphours and remaining battery capacity. It is equipped with an internal programmable alarm relay, to run a generator when needed or to turn off devices when the battery voltage exceeds programmable boundaries. Defining the amount of energy available in a battery is a complex task since battery age, discharge current and temperature all influence the actual battery capacity. High...

Remote for GP-SW-1500 (12 & 24V)

The GX Touch 70 is a display for our Cerbo GX. The 7″ touchscreen display give an instant overview of your system and allow to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, Their super slim waterproof design, top-mountable setup and simple installation bring a lot of flexibility when creating a crisp and clean dashboard. Victron GX Touch 70 Information: Cerbo GX, Cerbo-S GX & GX Touch Specsheet ...

Xantrex, 710-0010, MPPT Charge Controller Remote Panel w/ 25' Cable. The Xantrex Solar 710-0010 MPPT Remote Panel provides remote monitoring and setting of Xantrex Solar MPPT Charge Controller parameters. The 710-0010 remote's LCD panel displays real-time system data including PV array voltage, amps, and watt-hours, as well as battery voltage and temperature from a remote location. Includes 25ft cable for remote mounting.OWNER'S GUIDE ...

The Outback MATE 2 Remote Display and controllers are complete management tools for your OutBack Power system. Through the use of a single MATE you can remotely manage and monitor multiple inverter/chargers, MX60s and any future OutBack power conversion and control products. The MATE and MATE2 are packed full of features to make system management simple. The easy-to-read 3.1" (8 cm) LCD is backlit for dark operating conditions. Four soft keys allow easy context-based navigation of menus and...

OutBack Mate 3 System Display and Controller make it easier to program and monitor a complete OutBack Power system.OutBack Mate3 Features:Program, Manage & Monitor Entire SystemIntuitive Menu StructureEasy-To-Read Graphical DisplaySystem Configuration WizardInternet EnabledField UpgradableUp to 1-Year of Data LoggingSD Memory Card Slot More detailed information: OutBack Mate 3 Specs ...

The new Rutland 1200 Remote Digital Display is designed to be conveniently located on board, you can view the actual performance, operating condition and remotely shutdown. Thee Rutland Remote Digital Display offers a number of optional screens for continuous display: wind power generation, solar generation or the default screen where both these, battery voltages and charge status are displayed. Rutland Remote Digital Display Specs Push buttons simply scroll through the screen and access...

Victron Cerbo GX System Monitoring ensures that all your energy installationsystem-components - such as inverter/chargers, solar chargers, and batteries work in harmony. Simply connect through the Victron Remote Management Portal (VRM), or access directly, using the separate GX Touch 50, a MFD or the VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in...

Victron Cerbo-S GX System Monitoring ensures that all your energy installationsystem-components - such as inverter/chargers, solar chargers, and batteries work in harmony. Simply connect through the Victron Remote Management Portal (VRM), or access directly, using the separate GX Touch 50, a MFD or the VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in...

Victron GX Touch 50 is the 5″ touchscreen display accessory for the Cerbo GX. It gives instant overview of your system and allows to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, its super slim waterproof design, top-mountable setup and its simple installation bring a lot of flexibility when creating a crisp and clean dashboard. Victron GX Touch 50 Information: Cerbo GX, Cerbo-S GX & GX Touch Specsheet "Unboxing the new Cerbo GX &...

The TRUECHARGE 2 Remote Panel (808-8040-01) is designed for use with TRUECHARGE 2 Battery Chargers. This full-function remote allows you to monitor and control battery charger performance from a remote location, including features not accessible from the charger’s onboard display. The TRUECHARGE 2 Remote Panel reads like a fuel gauge and displays critical information on charging of battery banks. It is very easy to install, read and operate, connecting with the battery charger through the...

SCAD MLC Masthead Light Controller provides touch control of LED masthead lights, distress signalling and a visual display of the light's status. The controller easily installs on existing two or three wire LED lights. MLC Light Controller Features: Controls three functions of LED masthead lights: 1. Tri­color on/off; 2. Anchor on/off; 3. Distress signalling (strobe and SOS) Works with two and three wire systems; Touch control; Visual display of masthead light...

E Battery External Display Panel is used to connect with E-Series Battery to show the state of charge, current and voltage information of the battery system.  Part Number: EB-DP00-00 Vaquita Drive information: Vaquita Quick Start Vaquita Manual --> ...

The SmartSolar Control Display is a pluggable LCD display for the SmartSolar Charge Controllers. Simply remove the rubber seal that protects the plug on the front of the controller and plug-in the display. Manufacturer Part #:  SCC900650010 VE.Bus Smart Dongle Information: VE.Bus Smart Dongle Manual --> ...

Victron Digital Multi Control Remote is design both for Multiplus and Quattro Inverter Chargers. It allows PowerControl and PowerAssist current limit setting for two AC sources: a generator and shore-side current for example. Fixed setting range (for both models): 200 Amps. The brightness of the LED's is automatically reduced during night time. Connecting cable not included for the VE.Buss interface. Recommend the use of these connecting cables (CLICK HERE). ...

EcoFlow 7" diagonal touch screen Remote Display used in conjunction with the EcoFlow Prepared Kits.  RJ45 cable communicates via CAN buss and interconnects by hard wire interface allows display of systems status.  Excellent addition for those who like "at hand" information if the form of a mounted display providing intuitive control of the entire power system. Dimensions: 8.1" Long x 4.5' High x .9" DeepWeight:  1.1 lbsOperating Temp: -13 to 140 F P/N: ZMM100MT-US ...

View the display information of the HRDi controller at a more convenient location such as the instrument panel- Recess Panel Mount- Reprogrammable features- 3m connecting cable supplied- Can be used to stall Windcharger

Wear it on the wrist or fix it to a paddle with a loop band. 8 forward speeds. Safety features: overboard protection, one-step emergency stop, abnormal status indication and low battery warning. Part Number: VA-RC00-00 Vaquita Drive information: Vaquita Quick Start Vaquita Manual --> ...

The IPN-Remote display provides basic monitoring for Blue Sky Energy�s IPN compatible charge controllers. The unit displays battery voltage, output current and charge control system status for up to 8 charge controllers on a single IPN network. A bright crisp low power LED display is used to provide excellent readability in any lighting. The Charge Status indicator displays present charge control system status, and shows relative battery state of charge. The versatile IPN-Remote shows battery...

The IPN-ProRemote combines full-featured charge solar controller monitoring station  into a single user friendly remote display. A bright crisp backlit LCD display with plain English language text and three simple front panel keys is extremely easy to use. The IPN-ProRemote also monitors and controls BlueSky Energy's IPN based charge controllers. It can monitor both the combined total and individual status of up to eight IPN charge controllers on a single IPN network. Depending on...

The ProTouch 3.5" Touchscreen Remote Display is a 3.5” flush-mounting touchscreen display compatible with any Blue Sky Energy charge controller with IPN network capability. It provides a user-friendly graphic interface for monitoring your solar system as well as five preset battery charge profiles (Lead Acid and Lithium LiFePO4) for your charge controller. ProTouch without Shunt: Flush Mounting 3.5″ touchscreen display, solar and battery monitoring with 5 preset profiles, RJ-11 cable...

The PROsine Remote Interface Panel (Part # 808-1800) allows standard Xantrex Sine Wave Inverter LCD Display Panel to be mounted remotely in the location of your choice.  It comes with 30' (10m) of telephone cable.The PROsine Remote Interface Panel (Part # 808-1800) is for use with all models of PROsine 1000 & 1800 Inverter models.Features:Standard Telephone Jack Outlet for connection to LCD panelLED indicator for basic status monitoringON/Bypass switchMounts into the existing cavity in...

Magnum ME-ARC50 Remote Control allows to monitor and customize the operating parameters for your Magnum inverter/charger. The Magnum ME-ARC50 advanced remote control can be used on all Magnum inverter/charger models so there is no cross-platform confusion. The ME-ARC50 comes standard with a 50-foot, 4-conductor (twisted-pair) telephone cable and includes non-volatile memory (preserves adjustable settings, even if power to the remote or inverter is removed). Magnum ME-ARC50 Remote Features: LED...

The MPPT Control lets you see the status as well as setup all BlueSolar MPPT Charge Controllers that have a VE.Direct communications port. The new MPPT Control is mounted in the familiar BMV-700 series housing, maintaining a consistent and professional look to your panels and systems monitoring equipment. To easily mount the MPPT Control on a wall, instead of flush mounted in a panel, use one of our wall mount enclosures. See the related products slider below. Features View live status...

XW System Control (FGA# 865-1050)The XW System Control Panel features a graphical, backlit liquid crystal display that displays system configuration and diagnostic information for all devices connected to the network. When installed as a XW Power System accessory, the XW System Control Panel eliminates the need for separate control panels for each device and gives a single point of control to set up and monitor an entire XW Power System.