Victron Energy

The Victron Charger Control panel (also known as the Phoenix Charger Control panel) provides remote control and monitoring of the charge process with LED indication of the charger status. In addition, the remote panel also offers output current adjustment that can be used to limit the output current and thus the power drawn from the AC supply. This is particularly useful when operating the charger from limited shore power or small gensets. The panel can also be used to change the battery...

The GX Touch wall mount accessory allows easy mounting of the GX Touch on a solid wall. No drilling or cut-out is required, other than the three screws that fix the wall mount onto the wall.

The Lynx Class-T Power In connects and fuses up to two strings of Lithium batteries. It features a positive and negative busbar, and connections for two Class-T fuses as well as a connection to ground the DC system. The Class T-fuses, available in 225A, 250A, 350A and 400A, must be purchased separately. For installations using three or more strings of Lithium batteries, use multiple Lynx Class-T modules. As a core component of the Lynx Distribution system, the Lynx Class-T seamlessly...

This is an 80 volt fuse is designed to fit the Lynx Shunt and has slots to accommodate a 3/8″ or 10mm stud.

Victron Energy Orion IP67 24/12 DC-DC Converters Victron Energy Orion IP67 24/12 DC-DC Converters are completely encapsulated: waterproof, shockproof and ignition protected. Water, oil or dirt will not damage the Orion IP67 DC-DC Converter. The casing is made of cast aluminium and the electronics are moulded in resin. Victron Orion IP67 Information:Orion IP67 DC-DC Converters DatasheetOrion IP67 DC-DC Converters Manual ...

The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine. When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set.Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual). If required, Bluetooth can be disabled. The Smart BatteryProtect is a...

The Blue Smart IP22 Charger is the new professional battery charger with built-in bluetooth. The Blue Smart IP22 Charger can be used on devices in your workshop and on motor vehicles, such as (classic) cars; motorbikes; boats and camper-vans. The Blue Smart IP22 Charger is the wireless solution to monitor voltage and current, to change settings and to update the charger when new features become available. Blue Smart IP22 Battery Charger: The highest efficiency ever! With up to 94% efficiency,...

The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth. For use in dual battery systems in vehicles or on boats where the alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch. The Orion-Tr Smart charger can be used in 12V or 24V systems and is suitable for both lead acid and lithium batteries. Models are...

A remote on-off switch for the Skylla-TG Charger.

Lithium SuperPack 12,8V & 25,6V Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, not needing any additional components.The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. The batteries can be connected in parallel. Series connection is not allowed. DATA SHEET ...

The VE.Bus BMS V2 is a Battery Management System (BMS) designed to interface with and protect a single, or multiple Victron Lithium Battery Smart 12,8V & 25,6V (LiFePO4 or LFP) in systems that have Victron inverters or inverter/chargers with VE.Bus communication. It monitors and protects the batteries against over voltage and under voltage of any individual cell, and also over temperature or under temperature conditions. Based on the status of the battery or batteries, the BMS will: Generate a...

The Battery Alarm is a small and low cost alarm panel which monitors your battery bank. It features both audible and visual alarms, as well as a potential free contact with normally open and normally closed contacts. Alarm thresholds and hysteresis are programmable by DIP switches. See manual for more information.Instruction installMore Info ...

The Battery Switch ON/OFF 275A is suitable for battery systems up to 48V. It has a unique ergonomic and aesthetic knob design. The knob is removable for isolation or safety purposes. The Battery Switch can be either surface or panel mounted, providing flexibility during install. The Battery Switch meets the ISO8846 Ignition Protection standard and is suitable for use in an engine room.DATA SHEET ...

VE.Bus to BMS 12-200 alternator control cableDATA SHEET

Lithium SuperPack 12,8V & 25,6V Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, not needing any additional components.The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. The batteries can be connected in parallel. Series connection is not allowed. DATA SHEET ...

Victron Energy MPPT 75/10 (12/24V - 10A) Charge current up to 10 A and PV voltage up to 75 VThe BlueSolar Charge Controller will charge a lower nominal voltage battery with a higher nominal voltage PV array. The controllers automatically adjust to 12 V or 24 V nominal battery voltage. Feature Highlights Ultra-fast Maximum Power Point Tracking (MPPT) Advanced Maximum Power Point Detection in case of partial shading conditions Load output on the small models BatteryLife: intelligent battery...

Victron Energy MPPT 75/15 (12/24V - 10A) Charge current up to 15 A and PV voltage up to 75 VThe Victron Charge Controller will charge a lower nominal voltage battery with a higher nominal voltage PV array. The controllers automatically adjust to 12 V or 24 V nominal battery voltage. Feature Highlights Ultra-fast Maximum Power Point Tracking (MPPT) Advanced Maximum Power Point Detection in case of partial shading conditions Load output on the small models BatteryLife: intelligent battery...

Lithium SuperPack 12,8V & 25,6V Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, not needing any additional components.The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. The batteries can be connected in parallel. Series connection is not allowed. DATA SHEET ...

Victron Energy MPPT 100/20 (12/24/48V - 20A) The BlueSolar Charge Controller will charge a lower nominal voltage battery with a higher nominal voltage PV array. The controllers automatically adjust to 12 V or 24 V nominal battery voltage. The SmartSolar MPPT 100/20 solar charge controller are Bluetooth accessible via either built in Bluetooth or the Victron Energy Bluetooth dongle. Utilizing the free VictronConnect app many parameters can be viewed and set, such as battery voltage, solar...

SmartSolar MPPT 100/30 (12/24V - 30A)The SmartSolar 100/30 MPPT Charge Controller with Bluetooth Smart built- in: enables set-up and monitoring with a smart phone or other Bluetooth enabled device. SmartSolar MPPT 100/30 Feature Highlights Ultra-fast Maximum Power Point Tracking (MPPT) Advanced Maximum Power Point Detection in case of partial shading conditions Outstanding conversion efficiency Flexible charge algorithm Extensive electronic protection Internal temperature sensor Real-time data...

Lithium SuperPack 12,8V & 25,6V Integrated BMS and safety switch The SuperPack batteries are extremely easy to install, not needing any additional components.The internal switch will disconnect the battery in case of over discharge, over charge or high temperature. The batteries can be connected in parallel. Series connection is not allowed. DATA SHEET ...

Victron Lithium Battery Smart LiFePO4 or LFP is the safest of the mainstream li-ion battery types. The nominal voltage of a LFP cell is 3,2V (lead-acid: 2V/cell). A 12V LFP battery therefore consists of 4 cells connected in series; and a 24V battery consists of 8 cells connected in series. Part Numbers: LiFePO4 100Ah: BAT512110610LiFePO4 160Ah: BAT512116610LiFePO4 200Ah:BAT512120610 LiFePO4 300Ah: BAT512130410 LiFePO4 330Ah: BAT512132410 Dimensions (HxWxD): LiFePO4...

Victron Energy MPPT 100/50 (12/24V - 50A)The BlueSolar Charge Controller will charge a lower nominal voltage battery with a higher nominal voltage PV array. The controllers automatically adjust to 12 V or 24 V nominal battery voltage. The SmartSolar MPPT 100/50 solar charge controller are Bluetooth accessible via either built in Bluetooth or the Victron Energy Bluetooth dongle. Utilizing the free VictronConnect app many parameters can be viewed and set, such as battery voltage, solar history,...

Victron Battery Monitors BMV-700 / BMV-702 Dual Bank are high precision battery monitors from Victron Energy. The essential function of a battery monitor is to calculate ampere-hours consumed and the state of charge of a battery. Ampere-hours consumed are calculated by integrating the current flowing in or out of the battery. The remaining battery capacity depends on the ampere-hours consumed, discharge current, temperature and the age of the battery. Complex software algorithms are needed to...