Rutland 914i Parts

Blocking diode isolation kit includes a easily mountable diode block along with (2) 12 – 10 gauge push-on crimps and hook up instruction sheet making installation a snap. A single stainless steel screw is required for mounting (not included). Rated 25A -400VRecommended for use with Rutland wind turbine controllers when the solar PV option is utilized.

Mast Mounting Kit: All the hardware to install your wind turbine including mast and stays. Includes the brushed aluminum 1.5" Schedule 40 (1.9"OD, 1.61" ID) mast and two 1" diameter SS stay pipes (8' long which will need to be cut based on installation needs). Also included is a hinged isolated mast base, two isolated 1" stay tie mounts and related hardware to install the mast. Each mast is e Marine fabricated to include the necessary holes for easy installation. If selected, the mast will be...

Heavy Duty Mast Mounting Kit: All the hardware to install your wind turbine including heavy duty mast and stays. Includes the Schedule 80 - 1.9" outside diameter  (1.5" ID)aluminum mast and (2) 1" diameter SS stay pipes (8' long which will need to be cut based on installation needs). Also included is a hinged isolated mast base, (2) isolated 1" stay tie mounts and related hardware to install the mast. Each mast is e Marine fabricated to include the necessary holes for easy installation....

Rutland 914i MPPT Assembly Board - MPPT PCB – 914i Part Numbers: MPPT PCB - 12V: SA-98/44 MPPT PCB - 24V: SA-98/45This item is non-returnable/non-refundable.

HRDi WIND / SOLAR CHARGE CONTROLLER - The latest wind & solar charge controller development from Marlec, the HRDi evolves from and improves on the successful HRDX controller.  The contemporary design meets the needs of ever increasing power demands and features a user selectable digital display.  The controller incorporates Pulse Width Modulation (PWM) technology to regulate battery voltage preventing overcharge.Charge control and dual battery bank charging for use with Rutland...

HRSi Charge Regulator - incorporates the latest Pulse Width Modulation (PWM) technology to regulate charge of the battery. Combined wind charger and up to 160 watts of solar panel input for single battery bank charging. Two tri-color LED's indicate charge status and battery voltage.  includes a Stop/Run switch. Works on 12 or 24 V systems and can be used  with Rutland 503 or 913 wind generators. An Isolation Diode is to be used when connecting solar panels to this controller. We also...

HRDi WIND / SOLAR CHARGE CONTROLLER - The latest wind & solar charge controller development from Marlec, the HRDi evolves from and improves on the successful HRDX controller.  The contemporary design meets the needs of ever increasing power demands and features a user selectable digital display.  The controller incorporates Pulse Width Modulation (PWM) technology to regulate battery voltage preventing overcharge. Charge control and dual battery bank charging for use with Rutland...

Set of 24 Blade Fasteners for Rutland 913/914i BladeRelated ItemRutland 913/914i Replacement Blade

Hardware for Rutland 913/914i Nose ConeNylon screws for securing the nose cone.Requires 3 screws for each nose cone.Part # 925-013

25 Amp 600 Piv Bridge Rectifier P.I.V. 1 1/8" square.

6 pin terminal block with barriers, clamping screws and see-through cover (included).  Rated at 25A, 50 V DC it provides an excellent solution for interconnect of large cables to small interface connections on small clamping terminal blocks found on the HRSi wind turbine regulator manufactured by Rutland.  We strongly recommend  this when large wires are used on the installation as a means of interconnecting to the controller to eliminate installation and operational...

Pin crimps allows easy termination of either 12 or 10gauge wire.  They feature a single pin that extends off the end of the crimp often required for interconnect to clamp type terminal blocks.  This makes for an excellent solution to difficult tight  wiring situations by eliminating the typical flying wire strands  when trying to insert stranded cables in a small tight clamping terminal strip.  These are strongly recommended for use with the HRDi wind charger...

Rutland 913/914i Replacement Brush Assembly. Includes 2 brushes and plastic mounting flange.

Rutland 914i Replacement Nose Cone (each), Hardware not included.Related Items:Hardware for Rutland 913/914i Nose Cone